Product Consultation
Your email address will not be published. Required fields are marked *

Content
A 550 mg turmeric blend arrives at the filling line in a 25 kg drum, and the first question the formulation team asks is rarely about the powder. It is about the shell. A size 0 capsule holds roughly 0.68 mL, which at a tapped density of 0.62 g/mL works out to about 420 mg, and the 550 mg label claim suddenly needs a size 00 shell, different change parts on the filling machine, and a revised specification. One letter on a document moves an entire production plan.
The quick answer most buyers need: size 0 and size 00 carry the overwhelming majority of commercial capsules, potent low-dose formulas step down to sizes 1, 2, 3 and 4, and the elongated 00B and 0EL shells exist for the awkward middle ground where a dose is just slightly too big for the standard shell but does not justify a larger diameter.
What follows breaks down every size in this manufacturer's range, converts the numbers into milligram fill weights, and flags the purchasing risks that show up when a size is chosen from a catalogue page instead of from a density measurement.
Capsule numbering runs in reverse order of physical size. A size 4 is the smallest shell in common use, and size 00 is the largest standard shell. The range supplied by this factory covers eight specifications: 00, 0, 1, 2, 3 and 4, plus the elongated 00B and 0EL.
Each step in the sequence changes volume by roughly 25 to 40 percent, which is a bigger jump than most people expect. That is why choosing one size too small is rarely solved by tamping harder, and why choosing one size too large leaves visible empty space and a light-looking fill.
Those milligram figures assume a powder with a tapped density near 0.8 g/mL and a realistic fill factor. A fluffy botanical extract at 0.45 g/mL will fit less than half of that into the same shell.
The table below puts the eight sizes side by side. Volume and dimensions come from standard industry shell drawings; the fill weight column is a practical guide rather than a promise.
| Capsule size | Volume (mL) | Typical fill at 0.8 g/mL (mg) | Locked length (mm) | Outside diameter (mm) |
|---|---|---|---|---|
| 00 | 0.95 | 600 to 700 | 23.3 | 8.5 |
| 0 | 0.68 | 430 to 500 | 21.7 | 7.6 |
| 1 | 0.50 | 320 to 380 | 19.4 | 6.6 |
| 2 | 0.37 | 240 to 290 | 18.0 | 6.4 |
| 3 | 0.30 | 190 to 240 | 15.9 | 5.8 |
| 4 | 0.21 | 130 to 170 | 14.3 | 5.3 |
| 00B | 1.10 | 700 to 820 | 25.5 | 8.5 |
| 0EL | 0.74 | 470 to 560 | 23.3 | 7.6 |
Two notes on reading this chart. First, the locked length is measured with cap and body fully seated, not the length of the two halves laid out separately. Second, a powder plug never fills the shell completely. A practical target is 75 to 90 percent of total shell volume, because the closing action needs clearance and because the cap must slide over the powder bed without shaving it.
The calculation itself is short. The judgment sits in the density number you plug into it.
Fill weight in mg = shell volume in mL x powder density in g/mL x 1000 x fill factor
Bulk density tells you what the powder does when it is poured. Tapped density tells you what it does after the filling machine has vibrated and tamped it. On a low-dose filling machine, the powder bed behaves closer to the tapped figure. A typical gap between the two readings is 15 to 35 percent, and on fibrous botanicals it can exceed 50 percent.
Use 0.85 for a well-flowing granulation on a dosing-disc machine, and 0.75 or lower for a sticky extract that bridges in the hopper. Never budget at 1.0.
Take a botanical blend with 0.48 g/mL bulk density and 0.66 g/mL tapped density. The label claims 300 mg. Using size 1 at 0.50 mL: 0.50 x 0.66 x 1000 x 0.85 equals about 280 mg, which falls short. Moving to size 0 gives 0.68 x 0.66 x 1000 x 0.85, or roughly 381 mg, comfortably covering the claim with room for weight variation. The size 0 shell costs more per unit and takes a slightly bigger carton, but it removes a filling shortfall that would otherwise trigger rejected batches.
These three sizes carry the bulk of global capsule demand, and the reason is simple arithmetic. Most supplement doses sit between 250 mg and 700 mg, and most powders sit between 0.5 and 0.9 g/mL. That combination lands squarely in size 1, 0 or 00.
Size 1 is the sweet spot for 250 to 320 mg doses of dense material, and it is also the easiest of the three to swallow for consumers who struggle with larger shells. Size 0 absorbs the middle of the market and is the most widely stocked and most economical of the mainstream shells. Size 00 handles 500 mg and above of moderate-density powder, but it is also where consumers start to notice the size in their hand.
One practical rule from production floors: if the chosen size leaves more than about 20 percent empty headspace after filling, the product will sound hollow when the bottle is shaken, and consumers read that sound as under-filling. Sizing tightly is a marketing decision as much as a technical one. For a step-by-step walkthrough of matching a dose to a shell, this guide on choosing the right gelatin capsule size covers the same reasoning from the formulation side.
Small shells exist for two reasons: high-potency ingredients and diluent-free formulations.
A 50 mg standardized extract does not need a 0.95 mL cavity. Filling it into size 00 means adding 600 mg of filler, which adds cost, adds a second ingredient to the label, and forces the consumer to swallow a large shell for a small active dose. Size 3 or size 4 solves all three problems at once.
Sizes 2, 3 and 4 are also common in multi-capsule regimens, where two small shells replace one large one. Consumers who avoid large capsules often accept two size 3 shells more readily than a single size 00. The trade-off is filling throughput, because small shells hold fewer milligrams per stroke of the dosator.
The two elongated specifications are the most misunderstood entries on a capsule size list. They do not change the diameter, and they do not change the swallowing profile in any meaningful way. What they add is length, and therefore volume.
A 00B shell extends the standard 00 body by roughly two millimetres. That extra length is worth about 10 to 15 percent more fill volume, which is often exactly the difference between a 650 mg formula fitting and not fitting. The 0EL does the same job for the size 0 family, adding near 9 percent.
Because the diameter is unchanged, elongated shells usually run on the same size 00 or size 0 change parts already on the machine, though the closing station height and the filled-shell handling rails need to be re-set. Confirm this against your own machine manual before committing to a production order, since closing station geometry differs between equipment builders.
All eight sizes are produced across the four material families, which means the material choice does not force a size compromise. What it does change is the handling window around the fill.
Gelatin shells sit at 12.5 to 16.5 percent moisture and stay flexible in that range. Below roughly 35 percent relative humidity in the filling room they turn brittle, and a size 4 shell cracks far more readily than a size 00 because there is less material to absorb the closing stress.
Gelatin capsuleMain Ingredients: Gelatin (usually derived from animal bones and skins such as cattle and pigs)View Product →
HPMC shells carry only 4 to 6.5 percent moisture and tolerate dry rooms and warm storage much better, which makes them the safer pick for tropical markets and for travel packs. Their dimensional consistency is also tighter, and they are not prone to the crosslinking reaction that can slow gelatin dissolution after long storage at high humidity.
HPMC capsuleMain Ingredient: HPMCView Product →
Halal shells follow the same size drawings and the same volume figures, so the fill weight calculation does not change. Buyers serving Muslim markets should confirm the raw material source chain rather than the size, since the size decision is purely geometric.
HALAL CapsuleMain Ingredients: Use gelatin or plant-based ingredients that comply with Islamic Halal certificationView Product →
Colored and pearl-finished shells behave identically in the filling machine. The only size-related caution is that opaque shells hide the powder level, so any under-fill becomes invisible to a visual inspection station and must be caught by weight check.
A size number is a nominal callout, not a dimensional guarantee. Two suppliers can both ship "size 0" and still differ enough to affect your filling machine.
Put these points in writing before a first order:
Ask for a sample of 300 to 500 shells in the exact size and run them on the actual filling machine with the actual powder. Machine trials catch problems that drawings never show, including static cling on small size 4 shells and cap shaving on dense granulations. Dimensional and moisture checks carried out on site, such as those performed in an in-house capsule chemistry laboratory, give a batch-level view of consistency rather than a single spot reading.
Size decides tooling. Change parts are size-specific, and a size 0 dosing disc will not run size 00 shells, no matter how the machine is adjusted. Before finalizing a size, confirm three things with the filling line: the available change parts, the maximum output per hour in that size, and the smallest fill weight the machine can hold reliably.
Small shells are slower. A machine rated at 100,000 capsules per hour in size 0 will typically lose 10 to 20 percent of that in size 3 or 4, because the smaller cavity fills and closes in less stable conditions. On a large annual volume, that throughput gap belongs in the cost calculation alongside the price per thousand shells.
Most complaints traced back to size selection fall into a handful of patterns.
Yes. Numbering runs in reverse. Size 00 is the largest standard shell in this range at roughly 0.95 mL, and size 0 holds about 0.68 mL, so a 00 is around 40 percent larger inside.
Between roughly 250 mg and 380 mg, depending on density. At 0.5 g/mL you get about 270 mg, and at 0.9 g/mL closer to 450 mg before the fill factor is applied.
Size 0 works if the tapped density is above about 0.7 g/mL. Below that, move to size 00 or 00B. The density reading decides it, not the milligram figure alone.
They do. HPMC, halal and pearl specifications follow the same 00 to 4 size drawings, with 00B and 0EL available as well, so a formula can switch material without redesigning the dose.
When a formula misses the standard 00 capacity by 5 to 15 percent. It is usually cheaper than adding a second capsule to the regimen or reducing the actives in the blend.
Plant-based shells handle liquid and semi-solid fills better than gelatin, and the seam is normally banded afterwards. Volume is set by the shell size exactly as it is for powders, but the fill line must be set lower to leave room for sealing.
Indirectly. A larger shell holds a larger powder plug, and a thicker plug wets more slowly once the shell opens. For fast-release claims, size 1 through 3 generally dissolve more predictably than a tightly tamped size 00.
Two is usually enough. Most single-product brands need one production size plus one alternative for reformulation. Stocking five sizes raises inventory cost and risks shell expiry before the second or third size is ever used.
Start with the dose, measure the tapped density, apply a fill factor of 0.85 or less, and let the arithmetic point to a size. Then check the practical constraints: is the size stocked, does the filling line have the change parts, and does the finished shell look properly filled in the consumer's hand.
Running that sequence takes an afternoon and prevents the far more expensive sequence of a rejected batch, a repackaged label and a delayed launch. The eight sizes cover every realistic dose from about 90 mg to over 800 mg, so the correct answer almost always exists inside the range already.
Your email address will not be published. Required fields are marked *
If you would like to learn more about our products, please feel free to contact us and we will do our to assist you.
No.1 Tianzhu 3rd Road, Dufu Town, Xinchang County, Zhejiang Province
86-575 8606 0065
86-159 8825 2009
+86 159 8825 2009
+1 380 215 7432
Copyright © Shaoxing Zhongya Capsule Co., Ltd. High Quality Empty Capsule Manufacturers Wholesale Transparent Empty Capsule Factory
All Rights Reserved.
